Featured Post

Beolover SyncDrive: DC Platter Motor Replacement for Beogram 4002 and 4004 (Type 551x and 552x)

Late Beogram 4002 and the 4004 (Types 551x and 552x), which have DC platter motors instead of the earlier synchronous AC motors usually suff...

Showing posts with label motor. Show all posts
Showing posts with label motor. Show all posts

Saturday, November 14, 2026

Beogram 4002 (5503): Installation of Commander Remote Control and New Carriage Motor

I recently sold a Beogram 4002 (Type 5503, with AC platter motor) to a Customer in California. I originally bought this unit from an eBay seller and restored it a few months ago. The restoration process is described here. My customer decided to upgrade the unit with a Commander Remote Control for AC motor Beograms and a new modern carriage motor that produces less vibration and noise than the original motors.

First, I exchanged the carriage motor. This shows the original motor still installed, together with the new Beolover aluminum pulley:


I unsoldered the leads and removed the motor assembly. This shows it together with the new Beolover Carriage Motor for Beogram 4000, 4002, and 4004:


I opened the enclosure up and removed the original motor:


The new motor with its two vibration-dampening rubber rings fits exactly like the old motor:


If you do this at home, make sure the motor is fully pushed to the wall of the enclosure towards the pulley end. I bolted the assembly back in and reconnected the leads:


After this, I did a quick function check. There are some original motors that have a reversed polarity. If the new motor seems to run in the opposite direction, simply reverse the leads. This motor conformed to the normal polarity pattern, and everything was o.k.. It ran noticeably quieter than the original motor. Beolovely!

This shows the kit:


The first step was removing the RPM panel. It easily pops out by pushing it a bit upwards on both ends with a suitable screwdriver. Use a piece of cardboard to protect the wood frame on the right side of the panel if you do this at home. This shows the removed panel:
The keypad is held down with one screw situated under the panel. I removed the screw and then slid the keypad PCB out of the keypad assembly. It is good to put it on a piece of foam or similar while working on it:
The first step of the Commander installation was soldering the keypad breakout to the terminals where the wiring comes into the keypad. This shows the solder terminals as I found them:


The first step is usually clearing a 'runway' for the small breakout PCB where it can sit flat on the keypad PCB. In this case, the pads were so oxidized that solder would not attach to them. I used a razor blade to remove the oxide layer, and then I tinned the pads with a bit of solder. I also removed some of the solder that held the wires in place, which resulted in a straight and flat area for the breakout PCB:


The next step was soldering the left- and rightmost contacts to the keypad pads while making sure the breakout is positioned vertically relative to the keypad PCB and in the right lateral position:

Note that some Beograms have keypad assemblies that require the breakout to be positioned with the white connector flush with the aluminum body to allow full re-insertion of the keypad PCB into the aluminum body. Once the breakout was positioned properly,  I soldered the remaining pads:

At this point, everything was ready for the Commander assembly to be bolted in. This shows it already connected with the keypad board via the provided white harness:


The final steps were sliding the keypad PCB back into the keypad aluminum body and then bolting the auto-repeat indicator under the keypad mounting screw:
I usually put a small strip of electrical tape on the red wiring harness of the indicator to keep things organized. There is not much space under the RPM panel once it is clipped in:
After this installation, I did a function check with the paired Apple remote, and everything worked perfectly.
I will now play it for a few more days, and then this lovely Beogram 4002 will be ready to travel to its new owner in California!










Thursday, October 29, 2026

Beogram 4002 DC Platter Motor Restoration

I recently received the DC platter motor of a Beogram 4002 from a customer in the UK for restoration.

This shows the unit as received:



I disassembled it to get the shaft bearing out for an oil infusion under vacuum:


The bearings are the two small donuts on the black pad upfront. 

I immersed them in synthetic oil and pulled a vacuum. Immediately, strong bubbling started, making some foam on the surface of the oil:

After a couple of days, the bubbling stopped, indicating that the pores of the Oilite bearing material were filled again with oil. The vacuum pulls out the air from the bearing material, which enables the oil to penetrate. Once the motor runs, the oil slowly leaks out onto the shaft, keeping it lubricated until the bearing material is empty again. Most small electric motors have such bearings.

I reassembled the motor and installed a new Beolover DC Platter Motor Pulley for Beogram 4002 and 4004. 


Unlike some offerings on eBay, etc., Beolover pulleys have the proper crowning to keep the belt centered.

I installed the motor in one of my 4002s and ran a 24 hrs RPM stability test with my BeoloverRPM device:

In its 'slow' mode, the BeoloverRPM allows logging of the RPM in 10s intervals to the serial port of a computer. The ASCII data can be plotted with any standard graphing program. This is the curve I obtained for this restored motor:

This curve is as good as it gets with the DC platter motors. There is a little bit of thermal drift due to ambient temperature changes, commensurate with analog motor control systems.

This motor is ready for duty again!

In case you wonder why there is some 'noise' on this graph: This comes from the fact that the BeoloverRPM essentially measures the time between platter ribs passing under its sensor and then calculates the RPM. Since the platter ribs spacing is slightly varying around the platter due to manufacturing tolerances, the RPM measurements are slightly affected by these distance variations. This can be seen if the BeoloverRPM is used in its 'fast' mode, where it sends an RPM measurement to the serial port whenever a platter rib passes:

The screen shows a pattern that repeats every 24 measurements. There are 24 ribs on the platter... This is a curve measured in this mode:


The data in this graph corresponds to 35 platter turns. The repeating platter-related pattern is superimposed on a slower sine-wavy shape. This slower pattern corresponds to 'wow-and-flutter', i.e., short-term RPM fluctuations. These are mainly caused by the feedback-based motor control system that keeps the motor RPM constant based on constant RPM measurements.






Monday, August 3, 2026

Beogram 4002: Restoration of DC Platter Motor

I recently received a Beogram 4002 DC platter motor from a customer in France for restoration. His Beogram had the usual randomly occurring RPM variations. Something that will most likely be fixed by re-infusing the dry motor shaft bearings with oil under vacuum. Most of these motors have bearings that lost all of their stored oil, and this causes the shaft friction to increase significantly.

This shows the motor as received:

I disassembled it to extract the shaft bearings:

The bearings are the two small donuts upfront on the black pad. I submerged them in synthetic oil and pulled a vacuum. Immediately, strong bubbling started around the bearings:
The bubbling indicates that air is being drawn from the pores of the Oilite-bearing material. The leaving air is successively supplanted by oil in a diffusion process. The process has completed when the bubbling stops. In this case, this happened after about two days. At that point, I extracted the bearings from the vacuum chamber:
Then I reassembled the motor with a new Beolover DC Platter Motor Pulley for Beogram 4002 and 4004 and installed it in my bench Beogram 4002 for testing with the BeoloverRPM device:
The BeoloverRPM is able to log the RPM in 10s intervals into a serial port of a computer over long periods of time. This allows precise detection of intermittent RPM deviations that otherwise would be difficult to detect. This is the graph I measured after about 24 hrs:


This flat curve is 'as good as it gets' with Beogram DC platter motors! This motor is ready for duty again! It is time to send this motor home to France for another tour of duty in its Beogram 4002!





 

Saturday, July 18, 2026

Beogram 4004 (5526): Upgrade With a New Beolover Carriage Motor and the Commander Remote Control System

I just sold a fully restored Beogram 4004 (Type 5526) that I offered via my store to a customer in California. Read here about the work done on this unit. My customer decided to get the unit upgraded with a new Beolover carriage motor and the Commander remote control.

The new carriage motors run much quieter than the original ones, and the Commander allows full control of all functions with an Apple remote. The Commander also adds auto-repeat functionality.

I put it on the bench and removed the aluminum panels. This shows the original motor still in place:

I extracted the motor, opened up the enclosure, and inserted the new Beolover carriage motor:
This shows the new motor installed:

Then I removed the keypad assembly to install the Commander remote control. Since this was a 4004, the Commander gets its power from the output PCB that is located under the keypad:
I plugged the Commander board into the keypad header on the main board and put the power breakout adapter into the keypad header on the output board. Then I connected the Commander with the white harness to the small jack on the breakout adapter: 
Here a detail shot of the power connection:
Then I plugged the keypad back in and bolted the autorepeat indicator in place with the main keypad mounting screw:
This concluded my work on the upgrades. Now I will play this Beogram a bit, and then it will be time to send it to its new owner.






Thursday, July 2, 2026

Beogram 8002: Skipping and Jerky Run-Off Carriage Motion - Installation and Test of a New Beolover Carriage Motor

It is good that I always listen to a restored Beogram for a while before I send it out. Some issues can only be detected after a longer period of use since they are intermittent or subtle. This also applied to the Beogram 8002 (Type 5633) that I recently sold to a customer in the UK. While I played it, I realized that the pickup occasionally skipped on records that I knew were perfectly fine. This only happened on a few sides that I played. But it indicated that something was wrong.

I encountered a similar issue a while back, where I resorted to tweaking the H-bridge gain to give the motor a bit more power. The reason for such behavior is increasing friction in the motor or elsewhere in the carriage mechanism, causing 'sticktion' where the motor does not get enough power to overcome static friction, while the arm moves inward on the record. After a few more turns of the record, the tracking sensor is finally at a point where the voltage at the carriage motor is high enough to overcome the stuck mechanism, and the motor suddenly starts running at a high speed so the carriage can catch up with the arm. This rapid catching-up process can cause sufficient mechanical turbulence that the very light tonearm skips a groove.

In this case, there was yet another indication that the motor had an issue: During runoff, the carriage moved in a few big jerky steps instead of a smooth, quick motion tracking the needle as the runoff groove drags it towards the center of the record until auto-return is triggered.

This time I thought, why not see if one can replace the Beogram 8002/8000 carriage motors with the Beolover Carriage Motor for Beogram 4000, 4002, and 4004. A quick measurement on the motor terminals indicated that the motors in the 8002 run at similar voltages to the motors in the 400x.

This shows the open carriage motor compartment of the 8002:

First, I unsoldered the brown lead and connected my multimeter in current measurement mode between the wire and the motor terminal. Then I operated the turntable to see what the maximum current might be that this motor draws:
As expected, the motor draws the most current (~70 mA) during the carriage return after pressing STOP.
I removed the motor:
This shows the original motor in comparison to the Beolover motor:
The new motor is a bit smaller. Like most new designs, it is more efficient than the original motors due to better magnets and better manufacturing techniques available today.
Due to the size difference, I had to design an adapter to make the new motor fit into the original motor housing. This is what I came up with:
I 3D-printed two plastic clam shells to increase the diameter and length of the motor to match the original form factor. The additional two EPDM rubber rings serve as vibration insulation. They are put on the motor like this:
Then the plastic pieces are fitted around the motor:
The plastic pieces have two protrusions that hold the motor in place and prevent it from sliding inside the housing:
The new motors have a small round mark next to one of the terminals. The brown wire needs to be connected where the mark is, and the blue one goes to the other terminal.
I soldered the blue wire:
Then I did another current measurement between the brown wire end and the unconnected motor terminal:
Like the original motor, this motor drew the largest current during carriage return. At 50 mA, it is about 30% smaller than the value of the original motor. This was to be expected. In the Beogram 400x series of turntables, I saw a similar power reduction for the same performance. Some things get better as time marches on!...;-). Lower power is always preferable. It reduces the stress on the H-bridge components and also results in a quieter and lower vibration operation. After this test, I connected the brown wire. Since it is shorter, I had to put in a wire bridge to extend it to the motor terminal:
The cover still fits perfectly:
This is how it looks from the front:
After this installation, I listened to a few records with the new motor, and everything worked very nicely. I noticed how much more quietly the motor operated during <</>> and START and STOP operations. Significantly fewer vibrations compared to the original motor! Beolovely!

At that point, I realized that it would be nice to get some oscilloscope shots of the tracking signal on the motor terminals. So I opened the motor housing again and connected my oscilloscope between the motor terminals. This trace gives a nice summary of the motor operation. It essentially captures the voltage fluctuations during the last few turns of the record before the 'run off' groove, then the signal during run off until auto-return is triggered, followed by the actual return:
I wanted to compare this signal with the original motor, and so I installed the original motor for another measurement. This shows the same operational sequence as above:
While the overall pattern looks similar, there are notable differences: The voltage jumps during regular tracking are larger for the original motor. They also have a higher baseline. This indicates that the tracking sensor needs to send more voltage before the motor moves. Secondly, the run-off signal confirms what I observed visually, that the carriage makes bigger jumps. Comparison to the new motor shows that the original motor moves in 3-4 big steps, while the new motor gets a much larger number of voltage pulses, causing it to move the carriage much more smoothly.

In summary, I think the Beolover carriage motor is an excellent substitute for the original motors, which seem to be on the verge to develop age related issues. If you are interested in upgrading your Beogram 8002 or 8000 with a new carriage motor, it is now available via the Beolover's DKaudiolover store!