Featured Post

Beolover SyncDrive: DC Platter Motor Replacement for Beogram 4002 and 4004 (Type 551x and 552x)

Late Beogram 4002 and the 4004 (Types 551x and 552x), which have DC platter motors instead of the earlier synchronous AC motors usually suff...

Showing posts with label 1751RKBG4002MOT. Show all posts
Showing posts with label 1751RKBG4002MOT. Show all posts

Wednesday, November 5, 2025

Beogram 4002 (5513): DC Platter Motor Not Spinning Anymore

I restored the PCBs, DC platter motor and RPM panel of a Beogram 4002 from a customer in California in January 2021. Recently he contacted me stating that the platter motor stopped spinning. I asked him to return the parts so I could have a look.

After I received them I implanted them in my bench 4002. Indeed the platter motor did not spin anymore! The culprit was found quickly after checking the motor voltage at the red wire of the motor harness. I only measured 2.4V. It should be around 9V if everything is o.k.

The motor voltage is stabilized by 1TR2, originally a TIP31 power transistor. Since the Zener diode still made ~10V, it was most likely the transistor. I replaced it with a stronger TIP41:
And everything was good again in the motor voltage department. 9.6V at the red lead!:
In 2021 I had not understood yet that the power transistors on these boards often have issues. Maybe age related, maybe just wear from years of playing records. Informed by repeat transistor failures that I encountered over the years, I now always replace them all when I restore a Beogram 400x. So I set out to update this board to my current state-of-the-art. It is best to replace the two power transistors mounted on the solder side of the board when the board is installed. It makes it easier to position them correctly that the mounting holes match up. This shows 1IC1, which regulates the 21V power rail. It is usually a TIP120:
I always try replacing power transistors with stronger types for enhanced longevity. In this case a TIP102 is a good choice:
For some reason modern TIP replacements need some capacitance at their emitter in this circuit configuration to prevent high frequency oscillations superimposed to their emitter output. That is why I soldered a 100nF cap (yellow-orange) between the emitter and a conveniently located GND solder point nearby in the above picture.
The second transistor on the solder side, 1IC4, is usually a TIP125, 
whose stronger cousin, the TIP107, makes a good replacement:
After this I removed the board and also replaced the often fail prone H-bridge transistors with new types. this shows the updated board with the extracted parts:
I installed the board again and successfully tested all functions. These parts are ready for duty again and will soon travel back home to their Beogram 4002 in California!


Tuesday, January 12, 2021

Beogram 4002 Type 5513: Restoration of DC Platter Motor, PCBs and RPM Panel

I recently received the DC platter motor, both PCBs and the RPM panel from a Beogram 4002 (5513) in California. As usual I started with the motor since it can take a few days until the oil infusion of the bearings is complete. This shows the motor as received:

I disassembled it to get the bearings out:
Then I immersed the bearings in motor oil and pulled a vacuum:
Immediately vigorous bubbling started, indicating that air was drawn out from the porous bearing material to make room for oil inter-diffusion. While the infusion was in process I focused on the remaining parts.
This shows the main PCB in its original condition:
A detail shot of the 'RPM section', consisting of two RPM trimmers and the original Siemens 33/45 switch relay:
This shows the original setup of the sensor arm amplifier. Replacing the transistor and installing a trimmer for adjusting its bias precisely should be part of any Beogram 4002 restoration:
This shows the board after rebuilding it:
A detail shot of the renewed RPM circuit:
and the sensor amplifier. The blue 'box' is a 25-turn precision trimmer to adjust the bias of the transistor.
The next step was to rebuild the output board. This shows it in original condition:
I replaced the output relay (it grounds the signal leads until the needle has safely landed on the platter), installed a switch that allows connecting system and signal grounds (this usually cures humming issues with RCA based amplifiers), and I replaced the capacitor that defines the time constant of the relay action during arm lowering:
The final part of this project was to replace the incandescent bulbs of the RPM panel. This shows it as received. One bulb cover appears to have gone missing, revealing one of the bulbs:
This are the LED boards before installation:
I put them in
and replaced the covers. Luckily I still had a spare cover:
then it was time to finish up by adjusting the sensor arm transistor bias to get 4V at its collector. 
After this was done I verified that the sensor signal was according to specifications. This shows the signal as measured with a rotating empty platter under the sensor:
Whenever a black rib passes under the sensor, the signal goes down to 0V. This signal looks very good. The final step was to put the DC motor back together, calibrate 33 and 45 RPM and then measure a RPM stability curve over 24 hrs with the BeoloverRPM device:
This is the curve I measured:
This is as good as it gets with the DC motor Beogram 4002. These parts are ready for for duty again and will soon be sent back to California!