Beomaster 4400 Type 2419: Personal Project: Reassembled and Ready for Listening Tests

I decided I would reassemble this Beomaster 4400 and start performing some listening tests with it before I do any performance testing and before I complete the cosmetic restorations.

The reason for that is I want to get my second Beomaster 4400 started and completed as soon as possible...while the soldering iron is hot :-).  That way I can test and compare both units together.

The second Beomaster will also require a little bit of cosmetic repairs.

First though I must fix the power on lamp on this Beomaster unit.
Here is the power on lamp assembly housing. I is a black plastic lamp housing that fits onto a metal bayonet that is part of the lamp lens inside the front of the cabinet. It just pulls off the bayonet for access to change the lamp.

The lamps fit really tight inside the housing to it takes some careful pulling to remove one.

Once the lamp was replaced the power on lamp worked again as well as the radicator lamp.
That makes sense as the power for the radicator lamp comes through the power on lamp.

Moving forward with the reassembly I installed new cabinet feet on the Beomaster cabinet bottom cover.  These Beomaster 4400 cabinet feet are usually rusty and flat.

On this Beomaster the feet are a little smashed down and one foot is missing. No rust though. That is a welcome site.

The replacement feet are much better and have a metal tube for the screw so the rubber doesn't get flattened out if somebody over torques the mounting screw.

I reattached the front slider control bar then the bottom plate and the top cover. This Beomaster is ready for some listening tests.

After I recap and change trimmers in the second Beomaster 4400 I will return and do some cosmetic touch ups on this one. The rosewood cabinet looks nice in the photos but the finish is a little dull. Plus there is the small chip on the left side. I also need to order a cover plate for the FM preset tuning dials. I can get that from Martin Olsen's Beoparts store.

Beomaster 4400 Type 2419: Personal Project: Initial Power Checks

I couldn't end the day with just having the board restoration work complete.

I am always curious whether the audio components will actually work now.

First step was to reinstall the preamplifier and FM boards.

The Beomaster is ready to power on. Like I always do with this type of amplifier I connect the power cord to my variac, ammeter, voltmeter and dim bulb test device.  That device will protect against any hidden short to grounds on the power signals and it will tell me if something is drawing too much current.

In this case...I got nothing. No lights, no voltage on the power supplies.

After a bit of investigation I discovered that one of the AC cable wires was not connected internally in the Beomaster.  That explains that.

I checked the other wires around it and checked for any shorts. Other than the disconnected AC wire everything else looked fine.

Here is my repair of the broken wire.

That looks much better.

On the second round of the power checks I still don't get any lights illuminating on the Beomaster 4400 but I do have power on the supplies.

Here are the +15 VDC and +35 VDC supply checks

and here are the ±35 VDC rail voltage checks

It looks like the Beomaster 4400 is ready for a quick listening check.

I did a quick, initial setting of the idle current for the output amplifiers by adjusting the left and right channel trimmers to get 10mVDC across the respective channel emitter resistors.

Once those were adjusted I connected an iPod Nano to the Tape 2 source input and used a pair of headphones to check if I had sound.

Success!

I connected up an FM antenna to the Beomaster 4400 antenna input and tried tuning a station.
Another success.  The FM tuner section is working great. The tuning indicator and stereo lamps do come on as well.

So for certain the Beomaster 4400 power on lamp is not working and the lamp that illuminates the radicator (the FM signal strength meter) is also not working.

I am not sure about the overload lamp but I can test that when I replace the power on lamp.

Beomaster 4400 Type 2419: Personal Project: Preamplifier board and FM boards

The remaining boards requiring some recapping restoration are the preamplifier board and the FM boards of the Beomaster 4400.

Again, the previous post here, show the before state of the boards.

On the preamplifier board I also replaced the six, single-turn trimmers for the Phono, Tape 1 and Tape 2 source inputs.

Here is the preamplifier board after the restoration work -

Here are the three FM boards (FM1: Tuner, FM2: IF Section , FM3: Stereo Decoder and Indicator).
There is one 10uF, 10V tantalum capacitor in the FM1: Tuner board. I measured it and it is right on 10uF so I left that capacitor alone for now.

...actually that photo is a little premature.  The board still needs a 1uF and 0.47uF capacitors as shown added in this next photo.

Now for the big step of reinstalling the boards and setting up the first power on test of this Beomaster.

Beomaster 4400 Type 2419: Personal Project : Main PCB Recap, New Reservoir Capacitors, New Trimmer Resistors

It may look low profile and small but recapping a Beomaster 4400 is quite a big desoldering and soldering task.

I finished replacing all of the electrolytic capacitors and trimmer resistors on the Beomaster 4400 main board. I also installed an arc suppression device like I installed on the previous Beomaster 4400 restoration project. The purpose of that device is to provide extra protection to the Beomaster power switch contacts.

Here is the Beomaster 4400 after the recapping (the before photos are in the previous post)

Here are some closer shots of the inside of the Beomaster 4400 after the recap.

and here is a closer look at the reservoir capacitors and the arc suppression device.

With the main board and chassis completed I can move on to the three FM boards and the preamplifier board.